JINK Tubular Motor Series

Compare Motor 16, 25 and 35, then choose the tube, power supply, rated torque and Matter network for your shade.

Motor 16, Motor 25 and Motor 35 studio views

JINK Tubular Motor Series

Eight stories by the window

From sunlight and fabric to the torque, power and fittings behind the shade.

By the window · Morning

In the morning, give the window back to the light.

Before breakfast is on the table, shadows from the trees are already moving across the window. Raise the shade a little to brighten the table and open the view. Later, when the sun reaches the glass directly, lower the fabric enough to soften the light.

By the window · Morning
Set the shade for what you’re doing.

Set the shade for what you’re doing.

At breakfast you want a bright table. At a desk you may need to keep direct light off the screen. Look at the window from the places you actually sit. That tells you which part of the glass the fabric needs to cover.

The movement starts at the window head.

The movement starts at the window head.

The tubular motor sits inside the roller tube and turns it to move the shade. Once you know how you want the light to fall, choose the tube, torque and power supply. What remains in view is the window line and the fabric.

Motor 16 · Small-window retrofit

A narrow window and a desk just big enough for a book.

The narrow window above the desk is far from a socket, and there is little space at the head. Start by measuring the opening. Record the clear width, tube profile and the location of both supports before choosing a motor.

Motor 16 · Small-window retrofit
Measure the room your hand needs.

Measure the room your hand needs.

Motor 16 matches 20, 25 or 28 mm tubes. Check the assembled length with the motor head, idler and brackets in place. If you choose the battery model, allow room to plug in the charging lead.

Same torque, two ways to power it.

Same torque, two ways to power it.

Both are rated 0.3 N·m and 33 rpm. Where there is no continuous supply, choose ZM16EL with a battery, a compatible controller and a Thread border router. Where continuous 5 V DC is available, ZM16E offers Wi‑Fi.

Back at the desk.

Back at the desk.

Lower the fabric and the direct sun moves off the page. Raise it a little and the tree comes back into view. The motor sits out of sight at the top of the small window.

Motor 25 · 38 mm grooved tube

A new fabric can change the torque you need.

The dining area needs more shade, but the plan is to keep the existing 38 mm grooved tube. Measure the new fabric, include the bottom rail and check how thick the roll will become. The fabric may be the only visible change, yet the motor now has a different load.

Motor 25 · 38 mm grooved tube
Choose the fabric you want to live with.

Choose the fabric you want to live with.

Hold the swatches against the window. Compare daylight through the cloth with the privacy you get after switching on the room lights. Then have the installer check the fabric and rail weight and the wound diameter.

Keep 25 rpm and choose the torque you need.

Keep 25 rpm and choose the torque you need.

Both continuous-power models are rated at 25 rpm. The 2 N·m version offers about 54% more rated torque than 1.3 N·m. Where continuous power is unavailable, check whether the 1.3 N·m Thread battery model meets the load calculation.

By the window · Afternoon

Half a shade of light. A whole assembly behind it.

In the afternoon, sunlight reaches the reading chair. Lower the shade halfway and the weave comes into view while daylight still reaches the page. As a wide shade winds up, the roll builds layer by layer. The bottom rail is still hanging from the fabric. Both affect how the motor should be sized.

By the window · Afternoon
Two swatches can build very different rolls.

Two swatches can build very different rolls.

Look at each swatch from the front and against the light, then check its thickness. Weight and thickness have separate effects. Thickness changes the wound radius, while weight affects the pulling force the motor must overcome.

Tube size is fixed. The working radius changes.

Tube size is fixed. The working radius changes.

The same pull at a greater working radius calls for more torque. Check thickness, suspended weight, roll diameter and friction, and allow headroom. Window width alone cannot determine whether 6 or 10 N·m is suitable.

Motor 35 · 230 V AC

A wide shade starts with the choices you make before installation.

The living room renovation includes a 230 V AC supply at the window. The designer has also chosen a thicker fabric. Now the question is how much torque the assembled shade needs and which shaft speed suits the project. Start with the weight and wound diameter.

Motor 35 · 230 V AC
If 6 N·m meets the calculation, compare 28 rpm.

If 6 N·m meets the calculation, compare 28 rpm.

ZM35E-6/28 has the higher rated speed of the two AC models. For the same roll radius, the fabric travels faster. Actual travel time still depends on the drop, fabric thickness and load.

For higher torque, consider 10 N·m.

For higher torque, consider 10 N·m.

ZM35E-10/17 offers about 67% more rated torque than the 6 N·m model and is rated at 17 rpm. Once selected, check the tube, drive wheel and brackets against the 570 mm drawing length. A qualified installer completes the wiring.

One last look before closing the recess.

One last look before closing the recess.

Make sure the cable exit and setup end are accessible and the wound fabric has room. Before handover, run the shade through its full travel and check for interference at the ends, rail and fabric edges.

Motor 35 · Thread battery

Keep the original window. Leave a way to recharge it.

The home is already occupied, and the manual shade is up for an upgrade. There is no continuous supply at the window. First check whether the existing tube and hardware can be retained. Then check how you will reach the charging end once the recess is closed.

Motor 35 · Thread battery
6 N·m at 20 rpm, if it suits the load.

6 N·m at 20 rpm, if it suits the load.

If the shade assembly fits a 6 N·m rating, select ZM35EL-6/20. It has the higher rated speed of the two battery models. If travel time matters, check it on the actual tube and fabric.

10 N·m at 10 rpm, for projects that need more torque.

10 N·m at 10 rpm, for projects that need more torque.

Where the project needs more torque, check the load and travel with ZM35EL-10/10. Both battery models use Matter over Thread with a controller that supports window coverings and a Thread border router.

Check access with the recess still open.

Check access with the recess still open.

The drawings show a 645 mm body and a 52 mm head. Check which way the charging plug inserts and leave enough room for your hand. At the next recharge, the plug should be all you need to handle.

By the window · Evening

The light goes on. The shade comes down.

During the day the glass frames a view outward. Once the room lights are on after dark, that view can go both ways. Lower the shade to screen the room, while keeping the reading corner warm and well lit.

By the window · Evening
Sit down and look from where you normally read.

Sit down and look from where you normally read.

The view from a chair differs from the view outdoors. With the shade at its usual position, look at the edges, where the bottom rail stops, and whether the room lights make the weave more transparent.

Plan for privacy when choosing the cloth.

Plan for privacy when choosing the cloth.

Screen, tightly woven and blackout fabrics each give a different result. Gaps at the sides also matter. Decide what privacy you need after dark, then have the installer check that the tube and motor can handle the fabric.

Fitting the assembly · Tube to brackets

From a photo of the tube end to a finished shade.

The inquiry says “40 mm.” The installer also sees a clear photo looking straight into the tube. Together with a measurement, it identifies a round or octagonal profile. That detail determines how the motor, crown and drive wheel fit together.

Fitting the assembly · Tube to brackets
Tell the two 40 mm profiles apart by looking inside.

Tell the two 40 mm profiles apart by looking inside.

Photograph the open end straight on and record the diameter, profile and groove location. Round, octagonal, 50 mm grooved and 55 mm grooved tubes need matching parts. Check where and how they engage.

The drive wheel transfers torque into the tube.

The drive wheel transfers torque into the tube.

The crown locates the tube at the motor head. The output shaft drives it through the drive wheel. At the other end, the idler and bracket support the tube. Check the spacing of both mounting points.

Run the shade through its full travel at handover.

Run the shade through its full travel at handover.

Check that the wound fabric clears the recess and the bottom rail clears the sill at the lower end. Record the motor, tube and adapter parts so a future service visit can refer back to the actual assembly.

Technical specifications

Motor 16 · 20 / 25 / 28 mm

ModelPowerMatter networkRated torqueRated speed
ZM16EL-0.3/33Lithium batteryThread0.3 N·m33 rpm
ZM16E-0.3/335 V DCWi‑Fi0.3 N·m33 rpm

Motor 25 · 38 mm grooved

ModelPowerMatter networkRated torqueRated speed
ZM25TQ-1.3/25100–240 V continuousWi‑Fi1.3 N·m25 rpm
ZM25TQ-1.3/25100–240 V continuousThread1.3 N·m25 rpm
ZM25TQ-2/25100–240 V continuousWi‑Fi2 N·m25 rpm
ZM25TQ-2/25100–240 V continuousThread2 N·m25 rpm
ZM25EL-1.3/25Lithium batteryThread1.3 N·m25 rpm

Motor 35 · 40 mm round or octagonal / 50 or 55 mm grooved

ModelPowerMatter networkRated torqueRated speed
ZM35E-6/28230 V ACWi‑Fi6 N·m28 rpm
ZM35E-10/17230 V ACWi‑Fi10 N·m17 rpm
ZM35EL-6/20Lithium batteryThread6 N·m20 rpm
ZM35EL-10/10Lithium batteryThread10 N·m10 rpm

Use a Matter controller that supports window coverings. Thread models also need a Thread border router.

Motor 35 in the JINK Official Store

Ask about other configurations and fittings
Chat with usWhatsApp

Review your selection

Your shopping bag

Your selection is saved in this browser.

Find something for your home.

Explore products and add your preferred configuration.

Choose your configuration

Select a configuration to see its price